unix networking

You need to know all the steps needed to configure IP addresses on a NIC card. Web site shopping cart applications frequently need an additional IP address dedicated to them. You also might need to add a secondary NIC interface to your server to handle data backups. Last but not least, you might just want to play around with the server to test your skills.
This section shows you how to do the most common server IP activities with the least amount of headaches.

Determining Your IP Address

Most modern PCs come with an Ethernet port. When Linux is installed, this device is called eth0. You can determine the IP address of this device with the ifconfig command.

[root@bigboy tmp]# ifconfig -a

eth0 Link encap:Ethernet HWaddr 00:08:C7:10:74:A8

BROADCAST MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:100

RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

Interrupt:11 Base address:0x1820

lo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0

UP LOOPBACK RUNNING MTU:16436 Metric:1

RX packets:787 errors:0 dropped:0 overruns:0 frame:0

TX packets:787 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:82644 (80.7 Kb) TX bytes:82644 (80.7 Kb)

wlan0 Link encap:Ethernet HWaddr 00:06:25:09:6A:B5

inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:47379 errors:0 dropped:0 overruns:0 frame:0

TX packets:107900 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:100

RX bytes:4676853 (4.4 Mb) TX bytes:43209032 (41.2 Mb)

Interrupt:11 Memory:c887a000-c887b000

wlan0:0 Link encap:Ethernet HWaddr 00:06:25:09:6A:B5

inet addr:192.168.1.99 Bcast:192.168.1.255 Mask:255.255.255.0

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

Interrupt:11 Memory:c887a000-c887b000

[root@bigboy tmp]#

In this example, eth0 has no IP address because this box is using wireless interface wlan0 as its main NIC. Interface wlan0 has an IP address of 192.168.1.100 and a subnet mask of 255.255.255.0
You can see that this command gives good information on the interrupts, or PCI bus ID, used by each card. On very rare occasions you might find that your NIC card doesn't work because it shares both an interrupt and memory access address with some other device. You can look at the contents of the /proc/interrupts file to get a listing of all the interrupt IRQs used by your system. In the example below we can see that there are no conflicts with each IRQ from 0 to 15 having only a single entry. Devices eth0 and eth1 use interrupts 10 and 5, respectively:

[root@bigboy tmp]# cat /proc/interrupts

             CPU0

   0:  2707402473          XT-PIC  timer

   1:          67          XT-PIC  i8042

   2:           0          XT-PIC  cascade

   5:      411342          XT-PIC  eth1

   8:           1          XT-PIC  rtc

  10:     1898752          XT-PIC  eth0

  11:           0          XT-PIC  uhci_hcd

  12:          58          XT-PIC  i8042

  14:     5075806          XT-PIC  ide0

  15:         506          XT-PIC  ide1

NMI:           0

ERR:          43

[root@bigboy tmp]#

If there are conflicts, you might need to refer to the manual for the offending device to try to determine ways to either use another interrupt or memory I/O location.

Changing Your IP Address

If you wanted, you could give this eth0 interface an IP address using the ifconfig command.

[root@bigboy tmp]# ifconfig eth0 10.0.0.1 netmask 255.255.255.0 up

The "up" at the end of the command activates the interface. To make this permanent each time you boot up you'll have to add this command in your /etc/rc.local file which is run at the end of every reboot.
Fedora Linux also makes life a little easier with interface configuration files located in the /etc/sysconfig/network-scripts directory. Interface eth0 has a file called ifcfg-eth0, eth1 uses ifcfg-eth1, and so on. You can place your IP address information in these files, which are then used to auto-configure your NICs when Linux boots. See Figure 3-1 for two samples of interface eth0. One assumes the interface has a fixed IP address, and the other assumes it requires an IP address assignment using DHCP.